Midas x Skolyx Moc toe boot brown pullup
$462
NOTE: See below for sizing guidance.
A classic moc toe boot model that we developed together with Indonesian Midas Bootmaker (the workwear brand for Winson Shoemaker), a manufacturer that has received a lot of attention in workwear circles lately for their extremely well-made hand welted shoes at an excellent price. This moc toe model is only available through Skolyx. Made in a very durable mid-brown pull-up leather that will develop great character over the years. Pull-up leather is aniline dyed and then finished with waxes and oils for excellent resistance and a soft touch, and when stretched it becomes lighter coloured in these areas, which means a natural, lovely character will develop with use. Made on the last Landshaker with a high roomy toe box that is perfect for moc toes.
Made entirely by hand (apart from the upper being machine stitched), the shoes are lasted by hand, hand welted and have a hand stitched sole seam, which here attaches the midsole, to which the super-lightweight Vibram wedge sole then is attached (note, new stock has the same type of wedge sole from Dr. Sole, in off-white, see photo. So currently some sizes have Vibram, some Dr Sole). We also have a higher specification than regular Midas shoes where we've chosen real leather for both the heel stiffener and toe puff, which moulds nicely to the foot and can be reshaped if needed, made from the same type of veg-tanned shoulder leather as the insoles.
The pull-up leather is quite special. It's developed by a friend to the Midas founder, who source local hides and buys his own tanning agents, and then travels to a tannery in Yogyakarta where he rents a few tanning drums and equipment for a short period, and stays there and tans the hides himself. Therefore batches are highly limited, and when they are out of stock it can take a long time before he can go back to the tannery and produce new leathers.
Indonesia is one of the world's foremost centres of manufacture of workwear boots, a tradition that dates back to when the country was a Dutch colony, but which has evolved and been refined over the decades since the country gained independence in the 1940s. Uniquely, however, they still do everything almost exclusively by hand, not with lasting machines, Goodyear machines and McKay machines for stitching and so on, but with awl, needle, knife, hammer etc. Production is in general very small-scale, Midas / Winson is a small workshop in Bandung with eight people that only makes about 30 pairs of shoes a month.
These are boots that are made to be worn hard, and will only look better and better with age. Have half length gusset tongue to prevent water or snow entering the shoe. Really solidly made in thick leather, both in terms of upper leather and insole leather, which requires some time to break in but then becomes as one with your feet (a good tip for easier break-in is to not use the top eyelets).
See more detailed specifications below, and read more detailed information about the shoes and about Midas Bootmaker here.
Construction:
Hand welted with handmade sole stitch.
Both heel and toe stiffeners are made of real leather, which conforms to the feet in the best way possible, and can be reshaped if necessary.
Sole:
Vibram Morflex lightweight rubber sole (note, new stock has the same type of wedge sole from Dr. Sole, in off-white, see photo)
Size:
Comes in full EU sizes, so 6,6 mm in length between each size, so not directly comparable to UK/US sizes. See below for further sizing guidance. When in between sizes, we recommend choosing the larger size and also order a thin insole in leather. If you are still uncertain on your size, please e-mail ktj@skolyx.se for further guidance.
Care:
If you want to maintain a natural patina, it's recommended to use Saphir Medaille d'Or Crème Nappa conditioner (which is like Bick-4 but without silicone). If you want to keep the original look as much as possible or cover larger marks, use Saphir Medaille d'Or Creme Pommadier shoe cream in cognac or medium brown. We do recommend using shoe trees in cedar wood to prevent cracks from excessive creasing and prolong the lifespan of the boots.
NOTE: See below for sizing guidance.
Fast worldwide deliveries
Exchange/return items until Jan. 7
Free shipping in EU on orders above €120
Data sheet
- Sole
- Rubber sole
- Last
- Landshaker
- Construction
- Hand welted
- Material
- Medium brown leather
- Brand
- Midas Bootmaker
- Gender
- Male
- Type
- Boots
- Width
- F (standard)
See in the text above for which specific products to use for these shoes.
Basic shoe care:
- Don’t use the same pair for two consecutive days
- Brush / wipe the shoes off after use
- Use shoe trees and shoehorn
- Treat leather with shoe cream / suede and textile with waterproofing spray
Learn more on these steps in this guide.
Further shoe care info:
Read this guide on how to clean, nourish and shine leather shoes.
For how to clean, refresh and protect suede and nubuck, read this guide.
Shipping & delivery
EU: 2-5 business days. Free shipping from €120.
Switzerland: 1-4 business days. Free shipping from €200.
Norway: 1-4 business days. Free shipping from 900kr.
USA: 2-5 business days. Free shipping from $300. No extra customs charges for orders under $800. VAT is deducted.
Rest of the World: 2-7 business days. VAT is deducted on orders outside the EU. Shipping cost varies by destination.
To read more about shipping and delivery click here.
When ordering engraved products, there is an additional delivery time of 5-8 working days. In the case of a special order (customized shoes where you choose the leather, sole, etc.) of shoes, so-called MTO (made to order) / GMTO (group made to order), the estimated delivery time is about 6-8 weeks.
Returns & exchanges
You may return or exchange whole or part of your order if you notify us within 14 days after you received your products. Return costs are covered by you and shipping of exchange products are covered by us.
Return and exchange rights do not apply to products with engraving, made to order products and group made to order products.
To read more about returns and exchanges click here.
chat
Comments (0)
More information
Midas Bootmaker x Skolyx
Listed below are the full specifications of these shoes, and how they differ from standard Goodyear welted shoes:
- Lasted by hand, using pliers and hand hammered nails. When the upper is pulled over the shoe last, this is done with two different machines on standard Goodyear welted shoes.
- Insole made of thick vegetable tanned shoulder leather where the holdfast for the welt seam is carved out by hand with a sharp knife. On regular welted shoes it's a slightly thinner leather insole with a canvas strip glued to it, to which the welt is stitched.
- The heel stiffener and toe puff are made from the same type of leather as the insole, where it's split into thinner pieces and these are then cut and skived by hand to act as stiffeners, which when attached by hand treated with starch-based paste which makes the leather stiff when dry. On regular welted shoes, the toe cap is made of celastic (plastic-impregnated textile that is heated and then keeps the shape of the last as it cools) and the heel stiffener is usually made of celastic or leather board (leather dust mixed with glue) that is preformed, in some cases (as on TLB Mallorca Artista) of real leather but often also then preformed.
- Welt stitch sewn by hand, with awl, needle and twisted thread. When the leather strip that runs around the shoe is attached to the upper leather and the insole, the seam on regular welted shoes is sewn with a Goodyear machine.
- Sole stitch sewn by hand. The seam that attaches the welt to the outsole, the one that is removed and remade when you resole the shoes (until the welt becomes too worn and needs to be replaced as well) and which is sewn with a McKay sewing machine on regular welted shoes.
- The bottom filling consists of a cork plate in the front part, instead of the cheaper cork mass usually used. At the waist is a metal shank covered with the same vegetable tanned leather as the insole is made of, otherwise often just cork mass is used here as well.
- The heel is built up layer by layer, and pegged by hand from both the bottom and the inside of the shoe. Almost all factory-made welted shoes use pre-built heels that are put on the shoes in one piece and pegged by machine.
Read even more about how the shoes are made and about Midas Bootmaker, and watch footage of the production, here.
Sizing guidance
Midas boots are made in full EU sizes, which means that the difference in length between each size is approximately one Paris Point 6,6 mm. That can be compared to UK/US sizing which is 8,46 mm difference between full sizes, 4,23 mm between half sizes. Therefore, one can't really directly compare Midas sizing to UK/US sizing. Furthermore, since these are boots with roomy, round toe boxes, the length between the toes and front part of the shoe is in general relatively short, especially compared to regular dress shoes.
Below you'll find measurements of the different sizes. We recommend approximately around 10 mm shorter feet. When in between sizes, choose the larger size and add a thin leather insole (note, our insoles are small in size, choose EU43 for shoes in EU42). Inner length is taken from the back point of the shoe furthest back and furthest front, with a shoe measurement device, shown in mm.
As mentioned, it's difficult to do direct comparisons to UK/US sizes, but to help further you can see the closest "true to size" UK welted dress shoes sizing below. Normally US sizing is 1 up from this (for example for Allen Edmonds 65 last or Viberg 2030 last), for some brands only 0,5 (for example for Alden Barrie). 
For further sizing guidance, please contact us at ktj@skolyx.se.
NOTE: See below for sizing guidance.
A classic moc toe boot model that we developed together with Indonesian Midas Bootmaker (the workwear brand for Winson Shoemaker), a manufacturer that has received a lot of attention in workwear circles lately for their extremely well-made hand welted shoes at an excellent price. This moc toe model is only available through Skolyx. Made in a very durable mid-brown pull-up leather that will develop great character over the years. Pull-up leather is aniline dyed and then finished with waxes and oils for excellent resistance and a soft touch, and when stretched it becomes lighter coloured in these areas, which means a natural, lovely character will develop with use. Made on the last Landshaker with a high roomy toe box that is perfect for moc toes.
Made entirely by hand (apart from the upper being machine stitched), the shoes are lasted by hand, hand welted and have a hand stitched sole seam, which here attaches the midsole, to which the super-lightweight Vibram wedge sole then is attached (note, new stock has the same type of wedge sole from Dr. Sole, in off-white, see photo. So currently some sizes have Vibram, some Dr Sole). We also have a higher specification than regular Midas shoes where we've chosen real leather for both the heel stiffener and toe puff, which moulds nicely to the foot and can be reshaped if needed, made from the same type of veg-tanned shoulder leather as the insoles.
The pull-up leather is quite special. It's developed by a friend to the Midas founder, who source local hides and buys his own tanning agents, and then travels to a tannery in Yogyakarta where he rents a few tanning drums and equipment for a short period, and stays there and tans the hides himself. Therefore batches are highly limited, and when they are out of stock it can take a long time before he can go back to the tannery and produce new leathers.
Indonesia is one of the world's foremost centres of manufacture of workwear boots, a tradition that dates back to when the country was a Dutch colony, but which has evolved and been refined over the decades since the country gained independence in the 1940s. Uniquely, however, they still do everything almost exclusively by hand, not with lasting machines, Goodyear machines and McKay machines for stitching and so on, but with awl, needle, knife, hammer etc. Production is in general very small-scale, Midas / Winson is a small workshop in Bandung with eight people that only makes about 30 pairs of shoes a month.
These are boots that are made to be worn hard, and will only look better and better with age. Have half length gusset tongue to prevent water or snow entering the shoe. Really solidly made in thick leather, both in terms of upper leather and insole leather, which requires some time to break in but then becomes as one with your feet (a good tip for easier break-in is to not use the top eyelets).
See more detailed specifications below, and read more detailed information about the shoes and about Midas Bootmaker here.
Construction:
Hand welted with handmade sole stitch.
Both heel and toe stiffeners are made of real leather, which conforms to the feet in the best way possible, and can be reshaped if necessary.
Sole:
Vibram Morflex lightweight rubber sole (note, new stock has the same type of wedge sole from Dr. Sole, in off-white, see photo)
Size:
Comes in full EU sizes, so 6,6 mm in length between each size, so not directly comparable to UK/US sizes. See below for further sizing guidance. When in between sizes, we recommend choosing the larger size and also order a thin insole in leather. If you are still uncertain on your size, please e-mail ktj@skolyx.se for further guidance.
Care:
If you want to maintain a natural patina, it's recommended to use Saphir Medaille d'Or Crème Nappa conditioner (which is like Bick-4 but without silicone). If you want to keep the original look as much as possible or cover larger marks, use Saphir Medaille d'Or Creme Pommadier shoe cream in cognac or medium brown. We do recommend using shoe trees in cedar wood to prevent cracks from excessive creasing and prolong the lifespan of the boots.
NOTE: See below for sizing guidance.